Menu

 

The NASA Task Book
Advanced Search     

Project Title:  New Insights on Solid-Liquid Interface Anisotropy Effects on Solidification Patterns of Pure and Alloy Systems in Microgravity Reduce
Images: icon  Fiscal Year: FY 2022 
Division: Physical Sciences 
Research Discipline/Element:
Physical Sciences: MATERIALS SCIENCE--Materials science 
Start Date: 04/25/2019  
End Date: 09/24/2021  
Task Last Updated: 03/21/2022 
Download Task Book report in PDF pdf
Principal Investigator/Affiliation:   Asle Zaeem, Mohsen  Ph.D. / Colorado School of Mines 
Address:  Department of Mechanical Engineering & Materials Science Program 
1523 Illinois St., CoorsTek 203 
Golden , CO 80401 
Email: zaeem@mines.edu 
Phone: (303) 384-2260  
Congressional District:
Web:  
Organization Type: UNIVERSITY 
Organization Name: Colorado School of Mines 
Joint Agency:  
Comments: NOTE: PI moved in summer 2018 to Colorado School of Mines from Missouri University of Science and Technology (Ed., 12/10/18) 
Key Personnel Changes / Previous PI: A PhD student and postdoc are partially supported to determine the solid-liquid interface energies and their anisotropy for Ti and Al-Cu alloys by molecular dynamics simulations
Project Information: Grant/Contract No. 80NSSC19K0569 
Responsible Center: NASA MSFC 
Grant Monitor: Su, Ching-Hua  
Center Contact: 256-544-7776 
ching.h.su@nasa.gov 
Unique ID: 12494 
Solicitation / Funding Source: 2015-16 Physical Sciences NNH15ZTT001N-15PSI-C: Use of the NASA Physical Sciences Informatics System – Appendix C 
Grant/Contract No.: 80NSSC19K0569 
Project Type: Ground,Physical Sciences Informatics (PSI) 
Flight Program:  
No. of Post Docs:
No. of PhD Candidates:
No. of Master's Candidates:  
No. of Bachelor's Candidates:  
No. of PhD Degrees:  
No. of Master's Degrees:  
No. of Bachelor's Degrees:  
Program--Element: MATERIALS SCIENCE--Materials science 
Flight Assignment/Project Notes: NOTE: End date changed to 9/24/2021 per NSSC information (Ed., 4/22/21)

NOTE: End date changed to 4/21/2021 per NSSC information (Ed., 9/9/20)

NOTE: Period of performance per C-H Su/MSFC is 4/25/2019-4/20/2020 (Ed., 8/14/2019)

Task Description: NOTE: Continuation of "New Insights on Solid-Liquid Interface Anisotropy Effects on Solidification Patterns of Pure and Alloy Systems in Microgravity," grant 80NSSC18K045, when Principal Investigator was affiliated with Missouri University of Science and Technology.

The objective of this work is to study and predict the microscale patterns that develop in solidification of pure and alloy systems in microgravity, and investigate and compare the effect of solid-liquid interface anisotropy in microgravity and terrestrial conditions. A multiscale computational framework integrating molecular dynamics simulations and phase-field modeling will be utilized to quantitatively predict solid-liquid interface properties at the nanoscale and use these data to predict solidification patterns at the microscale.

Solidification of pure Al and Ti, and binary Al-Cu alloys are simulated to study and compare dendritic solidification patterns in microgravity and terrestrial conditions. The data generated by MICAST/CSS (Microstructure Formation in Casting of Technical Alloys under Diffusive and Magnetically Controlled Convective. Conditions/Comparison of Structure and Segregation in Alloys Directionally Solidified in Terrestrial and Microgravity Environments) 6 & 7 will be utilized to validate the computational modeling results.

The recently developed phase-field finite-element models in Principal Investigator's (PI) research group for predicting dendritic solidification patterns in pure and alloy systems will be modified and implemented in the Idaho National Lab’s MOOSE framework (Multiphysics Object-Oriented Simulation Environment) to study and predict three-dimensional microstructures of solidification. The required nanoscale input parameters for phase-field models, such as interface energies and anisotropy of Al-Cu alloys are calculated by MD simulations. It is essential to notice that most of the current mesoscale computational models do not include the actual interface energies and anisotropy coefficients, and only utilize arbitrary values to generate the desired patterns. The main focus of this work will be on studying the effects of solid-liquid interface properties on solidification patterns in microgravity condition; moreover some simulations at terrestrial gravity will be completed to compare the patterns at microgravity and terrestrial conditions. The validation in microgravity condition is particularly essential in order to confidently use the proposed multiscale model to study other pure and alloy materials in microgravity condition and compare their microstructures and segregation regions to those in terrestrial gravity.

The multiscale computational models that will be developed in this work can be used later to study solidification microstructures of other pure and binary alloys, and can be extended to study ternary alloys and ferrous metals in microgravity; this will result in developing the capability of accurately predicting solidification patterns and microstructures that develop in casting, welding, and laser and/or electron beam additive manufacturing in microgravity.

Research Impact/Earth Benefits: Since solid-liquid interfacial forces become dominant in the absence of the Earth’s gravity, we hypothesize that the proposed solidification phase field-simulations in microgravity conditions will enable us to fundamentally understand and distinguish transport phenomena, defect formation, and microstructural evolution mechanisms in traditional and advanced (e.g., additive) manufacturing processes in Earth’s gravity.

Task Progress & Bibliography Information FY2022 
Task Progress: The objective of this project was to study the effects of solid-liquid (SL) interfacial energy and its anisotropy on the microstructure development during the solidification of pure and binary systems. For this purpose, we developed an atomistic-informed phase-field (PF) framework to study the solidification of pure metals and binary materials. The simulations were run in microgravity conditions. Molecular dynamics (MD) was used to determine the anisotropic kinetic coefficient, SL interface energy, and other material properties to parameterize the PF models and the PF model predicts the formation and evolution of SL interface that affects the microstructures and properties of solidified metals and alloys. As a benchmark example for the solidification of alloys, we investigated the interactive effects of Cu concentration, SL interfacial energy properties, and cooling conditions on dendrite pattern and dendrite growth mechanisms during the solidification of Al-Cu alloys. In addition, we have developed a new atomistic-informed PF model for investigating the rapid solidification of pure materials. Unlike previous models and to consider the actual physics of crystal growth, the PF parameters, representing interface mobility, SL transformation barrier, and interfacial energy gradient, are temperature dependent. The parameters are determined by a combination of MD simulations and classical thermodynamic calculations based on the temperature-dependent SL interface properties and kinetic coefficient. For the benchmark example of Ti, the MD results show the average SL interface energy decreases with temperature, and the preferred dendrite growth direction shifts from <100> to <110> direction as the undercooling increases. PF simulations also show other favorite growth directions, implying that there is a competition between the interface anisotropy and kinetics of the SL interface. We specially investigated solidification of four Al-Cu alloys with 3%, 6%, 8.4%, and 10.6 at% Cu using atomistic-informed multi-phase field modeling. We investigated the combined effects of cooling condition, alloy composition and interfacial energy anisotropy on second phase (theta-phase) fraction and its distribution, and growth dynamics and morphology of solidification structures. First, the CM interfacial energies and its anisotropy were determined using molecular dynamic simulations. These values were used in phase-field simulations to quantitatively investigate the interactive effects of Cu content, CM interfacial properties, and cooling condition on growth dynamics and solidification patterns. Specific findings include the following: 1- Molecular dynamics simulation results showed that the CM interfacial energy decreases linearly with increasing Cu content while its anisotropy does not show a specific trend. 2- Phase-field simulation results showed that with increasing the cooling rate, the dendrite arm spacing and the amount of theta-phase decrease, and this reduction is more pronounced in alloys with higher Cu content. Also, the theta-phase fraction decreases by increasing the heat transfer coefficient. This reduction is due to the higher undercooling needed for eutectic reaction, which results in the formation of higher alpha-phase, and less liquid transforms into alpha+theta phase via eutectic reaction. Furthermore, the coring phenomenon is more noticeable at higher cooling rates which results in a reduction in Cu content in the interdendritic regions and a decrease in theta-phase. 3- Distribution of theta-phase is more homogenous in alloys with seaweed structures (Al-3 and Al-8.4 at% Cu) than the alloys with dendritic structures. In all investigated alloys, the distribution of theta-phase becomes more homogenous by increasing the heat transfer coefficient, but it is more sensitive to the value of heat transfer coefficient with seaweed structures. 4- Anisotropy of CM interfacial energy has a significant effect on solidification patterns and their growth dynamic. At the limit of diffusion control growth, when the strength of anisotropy is higher than 0.005 dendritic morphology is dominant at all cooling rates. At lower CM interfacial energy anisotropy different seaweed structures can form regarding constitutional supercooling at ahead of growing tip. When supercooling is less than 8K degenerate or fractal seaweed form while at higher supercoolings compact seaweed is dominant microstructure.

The results of this research are published in S. Kavousi, A. Gates, L. Jin, M. Asle Zaeem. A temperature-dependent atomistic-informed phase-field model to study dendritic growth, Journal of Crystal Growth 579 (2022), 126461 G. Azizi, S. Kavousi, M. Asle Zaeem, Interactive Effects of Interfacial Energy Anisotropy and Solute Transport on Microstructure Evolution of Al-Cu Alloys during Solidification Accepted in Acta Materialia (2022).

Bibliography: Description: (Last Updated: 03/23/2022) 

Show Cumulative Bibliography
 
Articles in Peer-reviewed Journals Kavousi S, Gates A, Jin L, Asle Zaeem M. "A temperature-dependent atomistic-informed phase-field model to study dendritic growth." Journal of Crystal Growth. 2022 Feb 1;579:126461. https://doi.org/10.1016/j.jcrysgro.2021.126461 , Feb-2022
Articles in Peer-reviewed Journals Azizi G, Kavousi S, Asle Zaeem M. "Interactive effects of interfacial energy anisotropy and solute transport on solidification patterns of Al-Cu alloys." Acta Materialia. 2022 Mar 22. https://doi.org/10.1016/j.actamat.2022.117859 , Mar-2022
Project Title:  New Insights on Solid-Liquid Interface Anisotropy Effects on Solidification Patterns of Pure and Alloy Systems in Microgravity Reduce
Images: icon  Fiscal Year: FY 2021 
Division: Physical Sciences 
Research Discipline/Element:
Physical Sciences: MATERIALS SCIENCE--Materials science 
Start Date: 04/25/2019  
End Date: 09/24/2021  
Task Last Updated: 02/23/2021 
Download Task Book report in PDF pdf
Principal Investigator/Affiliation:   Asle Zaeem, Mohsen  Ph.D. / Colorado School of Mines 
Address:  Department of Mechanical Engineering & Materials Science Program 
1523 Illinois St., CoorsTek 203 
Golden , CO 80401 
Email: zaeem@mines.edu 
Phone: (303) 384-2260  
Congressional District:
Web:  
Organization Type: UNIVERSITY 
Organization Name: Colorado School of Mines 
Joint Agency:  
Comments: NOTE: PI moved in summer 2018 to Colorado School of Mines from Missouri University of Science and Technology (Ed., 12/10/18) 
Key Personnel Changes / Previous PI: A postdoc is partially supported to determine the solid-liquid interface energies and their anisotropy for Ti and Al-Cu alloys by molecular dynamics simulations
Project Information: Grant/Contract No. 80NSSC19K0569 
Responsible Center: NASA MSFC 
Grant Monitor: Su, Ching-Hua  
Center Contact: 256-544-7776 
ching.h.su@nasa.gov 
Unique ID: 12494 
Solicitation / Funding Source: 2015-16 Physical Sciences NNH15ZTT001N-15PSI-C: Use of the NASA Physical Sciences Informatics System – Appendix C 
Grant/Contract No.: 80NSSC19K0569 
Project Type: Ground,Physical Sciences Informatics (PSI) 
Flight Program:  
No. of Post Docs:
No. of PhD Candidates:
No. of Master's Candidates:  
No. of Bachelor's Candidates:  
No. of PhD Degrees:  
No. of Master's Degrees:  
No. of Bachelor's Degrees:  
Program--Element: MATERIALS SCIENCE--Materials science 
Flight Assignment/Project Notes: NOTE: End date changed to 9/24/2021 per NSSC information (Ed., 4/22/21)

NOTE: End date changed to 4/21/2021 per NSSC information (Ed., 9/9/20)

NOTE: Period of performance per C-H Su/MSFC is 4/25/2019-4/20/2020 (Ed., 8/14/2019)

Task Description: NOTE: Continuation of "New Insights on Solid-Liquid Interface Anisotropy Effects on Solidification Patterns of Pure and Alloy Systems in Microgravity," grant 80NSSC18K045, when Principal Investigator was affiliated with Missouri University of Science and Technology.

The objective of this work is to study and predict the microscale patterns that develop in solidification of pure and alloy systems in microgravity, and investigate and compare the effect of solid-liquid interface anisotropy in microgravity and terrestrial conditions. A multiscale computational framework integrating molecular dynamics simulations and phase-field modeling will be utilized to quantitatively predict solid-liquid interface properties at the nanoscale and use these data to predict solidification patterns at the microscale.

Solidification of pure Al and Ti, and binary Al-Cu alloys are simulated to study and compare dendritic solidification patterns in microgravity and terrestrial conditions. The data generated by MICAST/CSS (Microstructure Formation in Casting of Technical Alloys under Diffusive and Magnetically Controlled Convective. Conditions/Comparison of Structure and Segregation in Alloys Directionally Solidified in Terrestrial and Microgravity Environments) 6 & 7 will be utilized to validate the computational modeling results.

The recently developed phase-field finite-element models in Principal Investigator's (PI) research group for predicting dendritic solidification patterns in pure and alloy systems will be modified and implemented in the Idaho National Lab’s MOOSE framework (Multiphysics Object-Oriented Simulation Environment) to study and predict three-dimensional microstructures of solidification. The required nanoscale input parameters for phase-field models, such as interface energies and anisotropy of Al-Cu alloys are calculated by MD simulations. It is essential to notice that most of the current mesoscale computational models do not include the actual interface energies and anisotropy coefficients, and only utilize arbitrary values to generate the desired patterns. The main focus of this work will be on studying the effects of solid-liquid interface properties on solidification patterns in microgravity condition; moreover some simulations at terrestrial gravity will be completed to compare the patterns at microgravity and terrestrial conditions. The validation in microgravity condition is particularly essential in order to confidently use the proposed multiscale model to study other pure and alloy materials in microgravity condition and compare their microstructures and segregation regions to those in terrestrial gravity.

The multiscale computational models that will be developed in this work can be used later to study solidification microstructures of other pure and binary alloys, and can be extended to study ternary alloys and ferrous metals in microgravity; this will result in developing the capability of accurately predicting solidification patterns and microstructures that develop in casting, welding, and laser and/or electron beam additive manufacturing in microgravity.

Research Impact/Earth Benefits: Since solid-liquid interfacial forces become dominant in the absence of the Earth’s gravity, we hypothesize that the proposed solidification phase field-simulations in microgravity conditions will enable us to fundamentally understand and distinguish transport phenomena, defect formation, and microstructural evolution mechanisms in traditional and advanced (e.g., additive) manufacturing processes in Earth’s gravity.

Task Progress & Bibliography Information FY2021 
Task Progress: Solid-liquid (SL) interfacial energy and its anisotropy play a crucial role in solidification pattern formation during alloy solidification. Due the length and time scale limitations of experiments, we used atomistic simulations to determine the values of SL interfacial energy and related anisotropy. The capillary fluctuation method was used for these calculations, and the microstructure evolution and pattern formation during solidification of pure Ti and different Al-Cu binary alloys were studied via multi-phase field modeling.

Majority of the phase-field models in the literature for study of solidification considered material properties and phase-field parameters to be independent of the working temperature. We have developed a model where all material properties and model parameters depend on the temperature. As a benchmark example, we have developed an atomistic-informed phase-field model for pure Ti where all the material properties were calculated by atomistic simulations. Temperature-dependent interface energy was determined using the CFM. But this requires obtaining the pressure-temperature phase diagram. We used molecular dynamics simulations using 2NN-MEAM interatomic potentials to calculate the coexistence line for the temperature ranging between -9 to 4 GPa. Then the coexistence line is used to determine the temperature-dependent solid-liquid interface free energy. The mobility as a function of temperature was determined based on the relations for the thin-interface analysis. The mean interface energy decreases by the increase of temperature and MD results were compatible with the analytical relation Thompson-Spaepen (Acta Metallurgica, 1979). The anisotropy parameters change in a way that that as the undercooling increases the {100} orientation becomes the preferred growth direction.

In comparison to the other phase-field models, the current results are more accurate and closer to the experimental results and analytical models. In order to validate our model, we compared the steady-state solidification rate obtained from the current PF model , the PF model by Karma and Rappel (Physical Review E, 1998) with two sets of experimental data. The results of both PF models are very close to experimental data for undercooling smaller than 200 K. In comparison to the PF model by Karma and Rappel, the current PF model presents a closer prediction to the experimental data as undercooling exceeds 200 K.

We also studied the solidification microstructures of Al-Cu alloys in different mediums with different heat transfer coefficients (h=0.5, 1.5, 5, and 10 w/cm2K). The atomistic simulations showed that the SL interface free energy decreases by a decrease of temperature or by an increase of solute atom concentration. It was shown that the alloy with 3 at% Cu is very sensitive to change of heat transfer coefficient especially in terms of dendrites pattern. When the heat transfer coefficient is low (h=0.5 w/cm2K) the dendrites are slightly tilted against heat transfer direction. Also, in low heat transfer coefficient a seaweed structure forms in this alloy. By increasing heat transfer, dendrites of Al-3%Cu alloy are aligned with heat transfer direction. On the other hand, dendrites of Al-6%Cu, Al-8.4%Cu, and Al-10.6%Cu are always in the direction of heat transfer direction regardless of heat transfer coefficient. In addition to change of dendrites growth direction in alloy with 3% Cu, dendritic patterns and morphologies noticeably differ with change of heat transfer coefficient in this alloy. When h=0.5 w/cm2K, the primary dendrites split in different places and a seaweed structure was formed. By increasing of h to 10 w/cm2K only columnar morphology was developed in Al-3%Cu alloy. On the other hand, in alloys with higher Cu content not seaweed structure at low heat transfer coefficient (h=0.5 w/cm2K) nor columnar structure at high heat transfer coefficient (h=10 w/cm2K) form. This behavior is related to interactive effects of interfacial energy anisotropy and solute transport phenomena. In higher Cu content concentration gradient ahead of growing interface override the effects of interface anisotropy.

Simulation and analytical results of primary dendrite arm spacing (PDAS) and secondary dendrite arm spacing (SDAS) at different heat transfer coefficient were compared and it was indicated that by increasing heat transfer coefficient, PDAS decreases in the all investigated alloys. In this study, the analytical equations which were driven by Dantzig and Rappaz (2016, EPFL press) were used to verify simulation results. It was shown that for a constant cooling condition (constant h value), PDAS is dependent on anisotropy of interfacial energy and concentration of solute atoms. The simulation results and analytical calculation indicated that by increasing SL interfacial energy, PDAS decreases. Also, the results showed that by increasing heat transfer coefficient from 0.5 to 10 w/cm2K, SDAS decreases but this reduction varies by change of Cu content. Also, by increasing Cu content SDAS decreased which indicates that finer microstructures are obtained in higher Cu content. The predicted primary dendrite arm spacing and secondary dendrite arm spacing showed very good agreement with analytical solutions and experimental data.

In this research, we have created an integrated computational scheme capable of quantitative predictions of solid-liquid interfacial effects on solidification patters and microstructures of pure and binary alloys. This quantitative computational framework is also transferrable to study solidification of other metals and alloys.

References

Thompson CV, Spaepen. On the approximation of the free energy change on crystallization. Acta Metallurgica Volume 27, Issue 12, December 1979, p. 1855-1859.

Karma A, Rappel W-J, Quantitative phase-field modeling of dendritic growth in two and three dimensions. Physical Review E, 1998. 57(4): p. 4323-4349.

Dantzig JA, Rappaz M, Solidification: -Revised & Expanded. 2016: EPFL press.

Bibliography: Description: (Last Updated: 03/23/2022) 

Show Cumulative Bibliography
 
 None in FY 2021
Project Title:  New Insights on Solid-Liquid Interface Anisotropy Effects on Solidification Patterns of Pure and Alloy Systems in Microgravity Reduce
Images: icon  Fiscal Year: FY 2020 
Division: Physical Sciences 
Research Discipline/Element:
Physical Sciences: MATERIALS SCIENCE--Materials science 
Start Date: 04/25/2019  
End Date: 04/21/2021  
Task Last Updated: 02/20/2020 
Download Task Book report in PDF pdf
Principal Investigator/Affiliation:   Asle Zaeem, Mohsen  Ph.D. / Colorado School of Mines 
Address:  Department of Mechanical Engineering & Materials Science Program 
1523 Illinois St., CoorsTek 203 
Golden , CO 80401 
Email: zaeem@mines.edu 
Phone: (303) 384-2260  
Congressional District:
Web:  
Organization Type: UNIVERSITY 
Organization Name: Colorado School of Mines 
Joint Agency:  
Comments: NOTE: PI moved in summer 2018 to Colorado School of Mines from Missouri University of Science and Technology (Ed., 12/10/18) 
Project Information: Grant/Contract No. 80NSSC19K0569 
Responsible Center: NASA MSFC 
Grant Monitor: Su, Ching-Hua  
Center Contact: 256-544-7776 
ching.h.su@nasa.gov 
Unique ID: 12494 
Solicitation / Funding Source: 2015-16 Physical Sciences NNH15ZTT001N-15PSI-C: Use of the NASA Physical Sciences Informatics System – Appendix C 
Grant/Contract No.: 80NSSC19K0569 
Project Type: Ground,Physical Sciences Informatics (PSI) 
Flight Program:  
No. of Post Docs:  
No. of PhD Candidates:
No. of Master's Candidates:  
No. of Bachelor's Candidates:  
No. of PhD Degrees:  
No. of Master's Degrees:  
No. of Bachelor's Degrees:  
Program--Element: MATERIALS SCIENCE--Materials science 
Flight Assignment/Project Notes: NOTE: End date changed to 4/21/2021 per NSSC information (Ed., 9/9/20)

NOTE: Period of performance per C-H Su/MSFC is 4/25/2019-4/20/2020 (Ed., 8/14/2019)

Task Description: NOTE: Continuation of "New Insights on Solid-Liquid Interface Anisotropy Effects on Solidification Patterns of Pure and Alloy Systems in Microgravity," grant 80NSSC18K045, when Principal Investigator was affiliated with Missouri University of Science and Technology.

The objective of this work is to study and predict the microscale patterns that develop in solidification of pure and alloy systems in microgravity, and investigate and compare the effect of solid-liquid interface anisotropy in microgravity and terrestrial conditions. A multiscale computational framework integrating molecular dynamics simulations and phase-field modeling will be utilized to quantitatively predict solid-liquid interface properties at the nanoscale and use these data to predict solidification patterns at the microscale. Three cases will be studied to benchmark against NASA Physical Sciences Informatics (PSI) database:

I. Solidification of ultra-pure succinonitrile (SCN) will be investigated; SCN is an organic crystal that forms dendrites similar to body-centered cubic (BCC) metals when it solidifies. The data generated by the Isothermal Dendritic Growth Experiment (IDGE) will be utilized to benchmark the computational modeling result for SCN. To identify similar effects in solidification patterns of BCC metals, our recent molecular dynamics (MD) simulations of iron (Fe, a BCC metal) will be utilized to build a quantitative phase-field model for predicting solidification patterns of pure Fe in microgravity.

II. Solidification of pivalic acid (PVA), a face-centered cubic (FCC) organic crystal that solidifies like many non-ferrous metals, will be investigated. PVA exhibits a large anisotropy of its solid-melt interfacial energy, which is a key parameter in the selection of dendritic growth. The data generated by IDGE will be utilized to benchmark the computational modeling results for PVA. To identify similar effects in solidification patterns of FCC metals, our recent MD simulations of aluminum (Al, an FCC metal) will be utilized to build a quantitative phase-field model for predicting solidification patterns of pure Al in microgravity.

III. Solidification of binary Al-Si and Al-Cu alloys will be simulated to study and compare dendritic solidification patterns in microgravity and terrestrial conditions. The data generated by MICAST/CSS (Microstructure Formation in Casting of Technical Alloys under Diffusive and Magnetically Controlled Convective. Conditions/Comparison of Structure and Segregation in Alloys Directionally Solidified in Terrestrial and Microgravity Environments) 6 & 7 on Al-Si will be utilized to validate the computational modeling results.

The recently developed phase-field finite-element models in Principal Investigator's (PI) research group for predicting dendritic solidification patterns in pure and alloy systems will be modified and implemented in the Idaho National Lab’s MOOSE framework (Multiphysics Object-Oriented Simulation Environment) to study and predict three-dimensional microstructures of solidification. The required nanoscale input parameters for phase-field models, such as interface energies and anisotropy of SCN, PVA, Al-Si, and Al-Cu will be calculated by MD simulations. It is essential to notice that most of the current mesoscale computational models do not include the actual interface energies and anisotropy coefficients, and only utilize arbitrary values to generate the desired patterns. The main focus of this work will be on studying the effects of solid-liquid interface properties on solidification patterns in microgravity condition; moreover some simulations at terrestrial gravity will be completed to compare the patterns at microgravity and terrestrial conditions. The validation in microgravity condition is particularly essential in order to confidently use the proposed multiscale model to study other pure and alloy materials in microgravity condition and compare their microstructures and segregation regions to those in terrestrial gravity.

The multiscale computational models that will be developed in this work can be used later to study solidification microstructures of other pure and binary alloys, and can be extended to study ternary alloys and ferrous metals in microgravity; this will result in developing the capability of accurately predicting solidification patterns and microstructures that develop in casting, welding, and laser and/or electron beam additive manufacturing in microgravity.

Research Impact/Earth Benefits: Since solid-liquid interfacial forces become dominant in the absence of the Earth’s gravity, we hypothesize that the proposed solidification phase field-simulations in microgravity conditions will enable us to fundamentally understand and distinguish transport phenomena, defect formation, and microstructural evolution mechanisms in traditional and advanced (e.g., additive) manufacturing processes in Earth’s gravity.

Task Progress & Bibliography Information FY2020 
Task Progress: 1. A multicomponent multiphase-field model for solidification of alloys systems under microgravity condition is developed.

2. A comprehensive study is completed by simulating solidification of Al-Cu system under microgravity condition to investigate the effect of solid/liquid interfacial energy anisotropy on:

- Primary Dendrite Arm Spacing ; - Primary Dendrite Trunk Diameter ; - Secondary Dendrite Arm Spacing ; - Primary Dendrite Average Growth Rate ;- Theta-phase (Al2Cu) fraction

Bibliography: Description: (Last Updated: 03/23/2022) 

Show Cumulative Bibliography
 
 None in FY 2020
Project Title:  New Insights on Solid-Liquid Interface Anisotropy Effects on Solidification Patterns of Pure and Alloy Systems in Microgravity Reduce
Images: icon  Fiscal Year: FY 2019 
Division: Physical Sciences 
Research Discipline/Element:
Physical Sciences: MATERIALS SCIENCE--Materials science 
Start Date: 04/25/2019  
End Date: 04/24/2020  
Task Last Updated: 08/14/2019 
Download Task Book report in PDF pdf
Principal Investigator/Affiliation:   Asle Zaeem, Mohsen  Ph.D. / Colorado School of Mines 
Address:  Department of Mechanical Engineering & Materials Science Program 
1523 Illinois St., CoorsTek 203 
Golden , CO 80401 
Email: zaeem@mines.edu 
Phone: (303) 384-2260  
Congressional District:
Web:  
Organization Type: UNIVERSITY 
Organization Name: Colorado School of Mines 
Joint Agency:  
Comments: NOTE: PI moved in summer 2018 to Colorado School of Mines from Missouri University of Science and Technology (Ed., 12/10/18) 
Project Information: Grant/Contract No. 80NSSC19K0569 
Responsible Center: NASA MSFC 
Grant Monitor: Su, Ching-Hua  
Center Contact: 256-544-7776 
ching.h.su@nasa.gov 
Unique ID: 12494 
Solicitation / Funding Source: 2015-16 Physical Sciences NNH15ZTT001N-15PSI-C: Use of the NASA Physical Sciences Informatics System – Appendix C 
Grant/Contract No.: 80NSSC19K0569 
Project Type: Ground,Physical Sciences Informatics (PSI) 
Flight Program:  
No. of Post Docs:  
No. of PhD Candidates:  
No. of Master's Candidates:  
No. of Bachelor's Candidates:  
No. of PhD Degrees:  
No. of Master's Degrees:  
No. of Bachelor's Degrees:  
Program--Element: MATERIALS SCIENCE--Materials science 
Flight Assignment/Project Notes: NOTE: Period of performance per C-H Su/MSFC (Ed., 8/14/2019)

Task Description: NOTE: Continuation of "New Insights on Solid-Liquid Interface Anisotropy Effects on Solidification Patterns of Pure and Alloy Systems in Microgravity," grant 80NSSC18K045, Missouri University of Science and Technology, PI's previous affiliation.

The objective of this work is to study and predict the microscale patterns that develop in solidification of pure and alloy systems in microgravity, and investigate and compare the effect of solid-liquid interface anisotropy in microgravity and terrestrial conditions. A multiscale computational framework integrating molecular dynamics simulations and phase-field modeling will be utilized to quantitatively predict solid-liquid interface properties at the nanoscale and use these data to predict solidification patterns at the microscale. Three cases will be studied to benchmark against NASA Physical Sciences Informatics (PSI) database:

I. Solidification of ultra-pure succinonitrile (SCN) will be investigated; SCN is an organic crystal that forms dendrites similar to body-centered cubic (BCC) metals when it solidifies. The data generated by the Isothermal Dendritic Growth Experiment (IDGE) will be utilized to benchmark the computational modeling result for SCN. To identify similar effects in solidification patterns of BCC metals, our recent molecular dynamics (MD) simulations of iron (Fe, a BCC metal) will be utilized to build a quantitative phase-field model for predicting solidification patterns of pure Fe in microgravity.

II. Solidification of pivalic acid (PVA), a face-centered cubic (FCC) organic crystal that solidifies like many non-ferrous metals, will be investigated. PVA exhibits a large anisotropy of its solid-melt interfacial energy, which is a key parameter in the selection of dendritic growth. The data generated by IDGE will be utilized to benchmark the computational modeling results for PVA. To identify similar effects in solidification patterns of FCC metals, our recent MD simulations of aluminum (Al, an FCC metal) will be utilized to build a quantitative phase-field model for predicting solidification patterns of pure Al in microgravity.

III. Solidification of binary Al-Si and Al-Cu alloys will be simulated to study and compare dendritic solidification patterns in microgravity and terrestrial conditions. The data generated by MICAST/CSS (Microstructure Formation in Casting of Technical Alloys under Diffusive and Magnetically Controlled Convective. Conditions/Comparison of Structure and Segregation in Alloys Directionally Solidified in Terrestrial and Microgravity Environments) 6 & 7 on Al-Si will be utilized to validate the computational modeling results.

The recently developed phase-field finite-element models in Principal Investigator's (PI) research group for predicting dendritic solidification patterns in pure and alloy systems will be modified and implemented in the Idaho National Lab’s MOOSE framework (Multiphysics Object-Oriented Simulation Environment) to study and predict three-dimensional microstructures of solidification. The required nanoscale input parameters for phase-field models, such as interface energies and anisotropy of SCN, PVA, Al-Si, and Al-Cu will be calculated by MD simulations. It is essential to notice that most of the current mesoscale computational models do not include the actual interface energies and anisotropy coefficients, and only utilize arbitrary values to generate the desired patterns. The main focus of this work will be on studying the effects of solid-liquid interface properties on solidification patterns in microgravity condition; moreover some simulations at terrestrial gravity will be completed to compare the patterns at microgravity and terrestrial conditions. The validation in microgravity condition is particularly essential in order to confidently use the proposed multiscale model to study other pure and alloy materials in microgravity condition and compare their microstructures and segregation regions to those in terrestrial gravity.

The multiscale computational models that will be developed in this work can be used later to study solidification microstructures of other pure and binary alloys, and can be extended to study ternary alloys and ferrous metals in microgravity; this will result in developing the capability of accurately predicting solidification patterns and microstructures that develop in casting, welding, and laser and/or electron beam additive manufacturing in microgravity.

Research Impact/Earth Benefits:

Task Progress & Bibliography Information FY2019 
Task Progress: New project for FY2019.

Continuation of "New Insights on Solid-Liquid Interface Anisotropy Effects on Solidification Patterns of Pure and Alloy Systems in Microgravity," grant 80NSSC18K045, Missouri University of Science and Technology, PI's previous affiliation.

Bibliography: Description: (Last Updated: 03/23/2022) 

Show Cumulative Bibliography
 
 None in FY 2019